Prekių katalogas

  • Pneumatinis smūginis veržliasukis 3/4", 1300Nm.

    Kodas: YT-09564
    18244 
    Šią prekę turime sandėlyje.
    Į krepšelį 
    Skaičiuojama...
    i

    Profesionalių įrankių linija.

    Prekės ženklas
    YATO
  • Indekso numeris YT-09564
    EAN 5906083095641
    Gamintojas YATO
    Slėgis [bar] 6,3
    Sukimo momentas [Nm] 1300
    [l / min] 660
    Dydis [colių] 3/4 "

    Product description
    A professional YATO pneumatic wrench. The size of the 3/4 "drive The maximum power obtained at 6 BAR is 1300 Nm.
    Usage
    Before each use of the tool, make sure that no parts of the pneumatic system are damaged. If any damage is observed, immediately replace it with new, undamaged system components.
    Before each use of the pneumatic system, condensed moisture should be dried inside the tool, compressor and hoses.
    Before starting work, attach an additional handle with four screws.

    Connecting the tool to the pneumatic system.
    - the figure shows the recommended way of connecting the tool to the pneumatic system. The shown method will ensure the most effective use of the tool and will extend the tool's life.
    - Add a few drops of SAE 10 viscosity to the air inlet
    - tightly and securely screw the appropriate end to the air inlet thread, allowing connection of the air supply hose (II)
    - attach a suitable tip to the tool carrier. For work with pneumatic tools, use only equipment adapted to work with impact tools
    - set the correct rotation direction (V). The direction of rotation is marked by an arrow. Adjust the pressure (torque)
    - connect the tool to the pneumatic system using a hose with an internal diameter of 1/2 ". Ensure that the hose has a strength of at least 1.38 MP. (III)
    - run the tool for a few seconds, making sure that no suspicious sounds or vibrations come from it

    Work with impact socket wrenches.
    Before screwing in the screw or nut, use a wrench to manually screw the threaded bolt or nut (at least two turns). Make sure that the size of the socket wrench is well-matched to the unscrewed or tightened element. Poor size selection can result in damage to both the key and the nut or bolt. The screw thread diameter must not exceed 21 mm.

    Unscrewing and tightening.
    - adjust the pressure in the pneumatic system so that it does not exceed the maximum value for the tool
    - set the right tool rotation direction and the appropriate torque (V)
    - Mount the appropriate socket wrench on the tool carrier (IV)
    - connect the key to the pneumatic system
    - put the key with the mounted cap on the unscrewed or tightened element
    - gradually press the trigger of the tool

    After finishing work, dismantle the pneumatic system and preserve the tool.
    Contents of the package
    The wrench is equipped with a connector that allows it to be connected to the pneumatic system.
    Technical data
    Index number YT-09564
    EAN 5906083095641
    Brand Yato
    PCS unit
    Gross weight (kg) 5.3330
    Pressure [bar] 6.3
    Torque [Nm] 1300
    Min / max 5000 revolutions
    Color box packaging
    The size of the quick connector [inch] 3/8 "
    Spindle size [mm] 3/4 "
    Yield [l / min] 660
    Size [inch] 3/4

    SQUARE DRIVE: 3/4″; AIR PRESSURE: 6-8KG/CM2; NO-LOAD SPEED: 5000R.P.M; CAPACITY BOLT DIA.: M21(MM); MAX. TORQUE: 1300N.M; AIR CONSUMPTION: 7CFM; AIR INLET: 1/4"; TWIN HAMMER IMPACT STRUCTURE; HANDLE EXHAUST; THREE SPEED OF POWER; HANDLE EXHAUST; COMFORTABLE GRIP; SUITABLE FOR LIGHT WEIGHT TRUCK; CAR TYRE MAINTENANCE; HEAVY DUTY MACHINERY
    Papildoma dokumentacija: